力士樂齒輪泵PGH4-20/040RE11VE4是維特銳集團專業供應的產品！力士樂齒輪泵PGH4-20/040RE11VE4的訂貨代碼是R900932162！力士樂齒輪泵PGH4-20/040RE11VE4可提供原裝專業供應！我們希望更多客戶前來咨詢了解力士樂齒輪泵PGH4-20/040RE11VE4！下面是相關的力士樂齒輪泵PGH4-20/040RE11VE4產品技術資料！希望得到你的認可！

力士樂齒輪泵PGH4-20/040RE11VE4特點固定排量
低操作噪音
低流量脈動
由于密封間隙補償，在低速和粘性下也具有率
適用于寬粘度和速度范圍
所有框架尺寸和尺寸可以任意組合
力士樂齒輪泵PGH4-20/040RE11VE4可與內齒輪泵，徑向柱塞泵和外齒輪泵組合使用

Product description

力士樂齒輪泵PGH4-20/040RE11VE4齒輪系統
力士樂齒輪泵PGH4-20/040RE11VE4的齒是漸開線齒系。 力士樂齒輪泵PGH4-20/040RE11VE4其大的嚙合長度導致很小的流量和壓力脈動; 力士樂齒輪泵PGH4-20/040RE11VE4這些小的脈動率顯著地有助于低噪聲運行。
力士樂齒輪泵PGH4-20/040RE11VE4屬于PGH型液壓泵是固定排量的間隙補償內齒輪泵。 力士樂齒輪泵PGH4-20/040RE11VE4流體動力安裝的小齒輪軸驅動內齒輪。 力士樂齒輪泵PGH4-20/040RE11VE4在吸入范圍中開口的小齒輪軸和內齒輪齒隙吸入液壓流體并將其輸送到壓力范圍。 力士樂齒輪泵PGH4-20/040RE11VE4吸力和壓力范圍由徑向補償元件和內齒輪和小齒輪軸之間的齒嚙合分開。

Set-up

Hydraulic pumps of type PGH are gap-compensated internal gear pumps with constant displacement.

They basically comprise of housing (1.1), bearing cover (1.2), internal gear (2), pinion shaft (3), plain bearings (4), axial washers (5), end cover (6), mounting flange (7) and stop pin (8), as well as the segment filler element (9) consisting of segment (9.1), segment support (9.2) and the seal rolls (9.3).

Suction and displacement procedure

The hydrodynamically supported pinion shaft (3) drives the internally geared internal gear (2) in the displayed direction of rotation.

During the rotation, there is a volume increase over an angle of approx. 90° in the suction range. An underpressure results and fluid flows into the chambers.

The sickle-shaped segment filler element (9) separates suction and pressure chamber. In the pressure chamber, the teeth of the pinion shaft (3) engage in the space between the teeth of the internal gear (2) again. The liquid is displaced via the pressure channel (P).

Axial compensation

The axial compensation force F_A takes effect in the area of the pressure chamber and is generated with the pressure field (10) in the axial washers (5).

So the axial longitudinal gaps between the rotating and the fixed parts are extraordinarily small and ensure perfect axial sealing of the pressure chamber.

Radial compensation

The radial compensation force F_R acts on segment (9.1) and segment support (9.2).

Dependent on the operating pressure, the two segment filler elements (9.1) and (9.2) are pressed against the head diameters of pinion shaft (3) and internal gear (2).

The area ratios and the position of the seal rolls (9.3) between the segment and segment support are designed so that an almost leakage gap-free sealing between internal gear (2), segment filler element (9) and pinion shaft (3) is achieved.

Spring elements under the seal rolls (9.3) ensure sufficient contact pressure, also with very low pressures.

Hydrodynamic and hydrostatic mounting

The forces acting on the pinion shaft (3) are accepted by hydrodynamically lubricated radial plain bearings (4); the forces acting on the internal gear (2) by the hydrostatic bearing (11).

Gear tooth system

The toothing is an involute tooth system. Its large meshing length results in little flow and pressure pulsation; these little pulsation rates considerably contribute to the low-noise running.

PGH-type hydraulic pumps are gap-compensated internal gear pumps with fixed displacement. The hydrodynamically mounted pinion shaft drives the internal gear. The pinion shaft and internal gear tooth clearances opening in the suction range suck in the hydraulic fluid and transport it to the pressure range. The suction and pressure range are separated by the radial compensation elements and the tooth engagement between the internal gear and pinion shaft.